DANFOSS EKC 102 A PDF

EKC Series – chennai india, EKC Series – chennai, EKC Series – , general ac EKC Series – , EKC Series – , ERC Series – chennai tamil . RI8NB R INSTRUCTIONS. EKC D (B). R Type: Pt Instructions RI8NB © Danfoss 05/ EKC D. EKC B Controller with two relay outputs, extra temperature sensor and digital EN and EN , A2 Weight = g Danfoss can accept no.

Author: Kazranos Galabar
Country: El Salvador
Language: English (Spanish)
Genre: Travel
Published (Last): 21 August 2018
Pages: 405
PDF File Size: 2.86 Mb
ePub File Size: 10.69 Mb
ISBN: 885-6-60971-395-5
Downloads: 80039
Price: Free* [*Free Regsitration Required]
Uploader: Zologar

Providing personal data is voluntary, but necessary for providing a reply. Access code 2 partly access Save the controllers present settings to the programming key. Sensors Sair is thermostat sensors. The contact will cut in when danfosz step 2 has to be cut in Defrost. To avoid a too high setting of the setpoint, the max.

All trademarks in this material are property of the respecitve companies.

The Danfoss controller is used for applications where temperature is critical. If there danfkss a status code, it will be shown on the display.

Access code 1 Access to all settings If vanfoss settings in the controller are to be protected with an access code you can set a numerical value between 0 and The defrost temperature cannot be displayed. A special moulding technique unites the hard front plastic, the softer buttons and the seal, so that they become an integral part of the front panel.

  JUSTICE HAMOODUR RAHMAN COMMISSION REPORT PDF

We also inform you that: Integrated refrigeration-technical functions Defrost on demand in 1: Natural defrost at stop of compressor.

Enter your e-mail address, to which we will send a one-time notification when this product is available again. However the view of —d- will be discontinued if: All starting methods will function in the controller. Defrost start can also be danfozs via contact signals or manual start-up. Via three pushes on a switch you change from one phase to the s phase. Temperature signal 2 can be used for defrost stop based on temperature or for product sensor.

HVAC Danfoss Electronic Temperature Controller type Danfoss EKC D B for Freezer

Low temperature alarm A4: There is no sensor -d-: The controller will register when the DI input is activated. The timer function starts when voltage is connected to the controller, but it is displaced the first time by the setting in d Here you set how large a slide of the S5 temperature can be allowed. The relay cuts in when higher temperatures are required remember to cancel defrost functions and compressor functions.

Activation can take place via r39 or input DI Alarm The controller can give alarm in different situations.

The input is not used 1 Status display of a contact function 2 Door function. Enter contact details and we will notify you, when the product is available.

HVAC Danfoss Electronic Temperature Controller type Danfoss EKC 102A 084B8500 for Freezer

EKC C Controller with two relay outputs, extra temperature sensor and digital input. There is no alarm delay.

  MAGNETROL LEVEL TRANSMITTER PDF

The setting will be the defrost time if d10 is selected to be 0 EKC c30 d01 d02 d03 d04 Time staggering for defrost cutins during start-up The function is only relevant if you have several refrigeration appliances or groups where you want the defrost to be staggered in relation to one another. The function delays the interval time d03 by the set number of minutes, but dwnfoss only does it once, and this at the very first defrost taking place when voltage is connected to the controller.

Push the middle button until the parameter value is shown 4. I want to receive an additional SMS with a notification Your phone number: If e,c defrost sensor registers a higher temperature than the danfoss set here, the fans will be stopped.

S5 is a defrost sensor and is used if defrost has to be stopped based on temperature. When there is defrost with clock function on the DI input the interval time must be set for a somewhat longer period of time than the planned one, as the interval time will otherwise start a defrost which a little later will be followed by xanfoss planned one. Refrigeration stopped by main switch.