AUTOMATIONDIRECT GS1 PDF

GS1 Drive Units ( / VAC) from AutomationDirect, the best value in industrial automation – low prices, fast shipping, and free award-winning service. Find great deals for Automation Direct Gsp0 VAC 2 HP 3 Ph Input Gs1 Series AC Micro Drive. Shop with confidence on eBay!. Find great deals for Automation Direct Gsp5 AC Micro Drive HP v. Shop with confidence on eBay!.

Author: Mijas Voodoolabar
Country: Botswana
Language: English (Spanish)
Genre: Literature
Published (Last): 16 August 2009
Pages: 445
PDF File Size: 10.92 Mb
ePub File Size: 1.6 Mb
ISBN: 760-9-79781-638-5
Downloads: 63724
Price: Free* [*Free Regsitration Required]
Uploader: Mukinos

Documents Flashcards Grammar checker. Prices as of April 15, Check Web site for most current prices. These drives can be configured using the builtin digital keypad which also allows you to set the drive speed, start and stop, and monitor specific parameters or with the standard RS serial communications port. Standard GS1 features include one analog input, four programmable digital inputs and one programmable normally open relay output.

Automation Direct Gsp5 AC Micro Drive HP v | eBay

See the comm cable matrix on page Servos and Steppers Motor Controls Sensors: Directional Control Valves Pneumatics: GS1 Specifications – Installation Company Information Drives Understanding the installation requirements for your GS1 drive will help to ensure that it will operate within its environmental and electrical limits.

Never use only this catalog for installation instructions or operation of equipment; refer to the user manual, GS1-M.

Limit Switches Altitude 1, m or less, indoors no corrosive gases or dust 2″ 50mm min Sensors: Protective structure is based upon EN Sensors: See our Web site for derating curves. The storage temperature refers to the short-term temperature during transport.

AC drives generate a large amount of heat, which may damage the AC drive. Auxiliary cooling methods are typically required in order to not exceed maximum ambient temperatures. Process Relays and Timers Pneumatics: Use twisted-shielded, twisted-pair or shielded-lead wires for the control signal wiring.

  01NET 793 PDF

It is recommended all signal wiring be run in a separate steel conduit. The shield wire should only be connected at the drive. Do not connect shield wire on both ends. Refer to user manual GS1-M for additional specific wiring automationdirrect. Current Fault Indication Sensors: Encoders Grounding resistance less than 0. Flow Pushbuttons and Lights RS 2: See the comm cable selection matrix on page Relays and Timers Pneumatics: Tubing Factory default setting Pneumatics: Air Fittings Factory default source of frequency command is via the keypad potentiometer Appendix Book 2 Main circuit power terminals Control circuit terminal Automationdirext leads Terms and Conditions Warning: Terminals 2 and 5 should not be used as a power source for your communication connection.

Automationdirect.com GS1-10P5 Manuals

GS1 Specifications – Dimensions Prewired cables keep installation clean and efficient, using half the space at a fraction of the cost of standard terminal blocks. See the following solutions to autoomationdirect determine the best ZIPLink system for your application. Using the Drives Communication selector tables located in this section, 1. Locate your Drive and type of communications.

Select a ZIPLink cable and other associated hardware.

Add a ZIPLink communications module to quickly and easily set up a multi-device network. Connections include a 6-pin RJ12 or 9-pin, pin and pin D-sub connectors which can be used in conjunction with the RJ12 or D-Sub Feedthrough modules.

Motors Using the Serial Communications Cables selector table located in this section, 1. Locate your connector type 2.

Limit Switches Solution 5: Locate the type of application. Select a ZIPLink module. ZIPLink Connector Modules to 3rd Party Devices If you need a way to connect your device to terminal blocks without all that wiring time, then our pigtail cables with color-coded soldered-tip wires are a good solution.

  ELECTRORRETINOGRAMA MULTIFOCAL PDF

Used in conjunction with any compatible ZIPLink Connector Modules, a pigtail cable keeps wiring clean and easy and reduces troubleshooting time. Select the number of pins.

Hitachi Drives Cross References Company Information Drives To find a suitable replacement for an SJ Hitachi drive, use the chart to the right to determine control mode s required, and the tables below to determine possible replacement part numbers.

Suggested replacements do not necessarily have all autoomationdirect modes of the original, so appropriate drives will be application-dependent. Please call Tech Support if there are any replacement questions. Photoelectric Possible Replacements Part No.

Replacement drives do not necessarily have the same physical dimensions, mounting hole patterns or wiring terminal arrangements. Replacement drive requires 3-phase power. Ensure that the existing SJ application uses 3-phase input power, or that 3-phase power is available. Output power of new drive can be parameter-limited to the smaller horsepower. Hitachi Drives Cross References To find a suitable replacement for an L or SJ Hitachi drive, use the chart to the right to determine control mode s required, and the tables below to determine possible replacement part numbers.

Automation Direct Gs1-22p0 230 VAC 2 HP 3 Ph Input Gs1 Series AC Micro Drive

Ensure that the existing application uses 3-phase input power, or that 3-phase power is available. Lab 08 Conservation automatiiondirect Momentum. Athens Innovation District BY: On asynchronous training in sensor networks Abstract coarse-grain.