ASTM F1554 GR 55 PDF

F Grade 55 Threaded Rod is manufactured from high strength, low alloy, 55 ksi yield strength steel. The F Specification is designed to cover Threaded. ASTM F is the standard specification for straight and bent, headed and Grade 55 – anchor bolts manufactured from modified mild steel with higher. The specification for ASTM F covers straight and bent, headed and headless, F Grade 55, High strength, low alloy, 55 ksi yield steel anchor bolts.

Author: Tygoran Dak
Country: Ecuador
Language: English (Spanish)
Genre: Science
Published (Last): 10 April 2011
Pages: 85
PDF File Size: 8.6 Mb
ePub File Size: 16.66 Mb
ISBN: 374-9-35824-656-2
Downloads: 62237
Price: Free* [*Free Regsitration Required]
Uploader: Kijar

The minimum Charpy V-notch energy requirement is an average of 15ft-lbs for three specimens, with no one specimen falling below 12ft-lbs.

Material Substitution Be skeptical of fastener distributors and manufacturers with limited manufacturing capabilities who attempt to substitute round bar or even A grade B7 material for F grade Br of the grade 55 round bar that Portland Bolt stocks will meet the S1 weldability requirements.

Leave a Comment Cancel reply Your email address will not be published.

ASTM F grade 55 anchor bolts are manufactured from a modified mild steel that has a higher minimum yield strength 55 ksi than traditional A36 mild steel 36 ksi. If weldability is required, supplementary requirement S1 must be specified. Overview ASTM F grade 55 anchor bolts are manufactured from a modified mild steel that has a higher minimum yield strength 55 ksi than traditional A36 mild steel 36 ksi.

It provides for anchor bolts in three strength grades, two thread classes, and in the diameters specified in Section 4. Your email address will not be published. If S1 is not specified by the purchaser, the Grade 55 material may or may not be weldable. F Grades F Grade 36 Low carbon, 36 ksi yield steel anchor bolts F Grade 55 High strength, low alloy, 55 ksi yield steel anchor bolts F Grade Alloy, heat treated, high strength ksi yield steel anchor bolts.

This specification was widely used in the light pole and traffic signal industry long before the ASTM F specification was introduced in and was commonly referred to as A36M In addition to standard round be… https: Supplementary Testing The following supplemental requirements apply to F Grade Grade 55 is more elastic and available at a lower cost, rendering it more applicable for general construction needs, while B7 is heat treated and contains alloys that make it more suitable for corrosive environments.

  BOWA ARC 350 PDF

The minimum Charpy V-notch energy requirement is an average of 15ft-lbs for three specimens, with no one specimen falling below 12ft-lbs. Portland Bolt buys mill runs of round bar and stocks this material for immediate processing. For example, common uses are in chemical and petroleum facilities. Contrary to popular belief, not all grade 55 material is weldable. The anchor bolts are furnished in three strength grades, two thread classes, and various sizes, and are intended for anchoring structural supports to concrete foundations such as building columns, column supports for highway signs, street lighting and traffic signals, steel bearing plates, and similar applications.

The three grades 36, 55, and designate the minimum yield strength ksi of the anchor bolt.

ASTM F – Portland Bolt

In this series, we will be covering four common topics to help you build the foundation you need to better understand the threaded fastener industry. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

We would like to congratula… https: Through chemical composition restrictions and by a carbon equivalency formula, S1 provides assurance of weldability. Hr ASTM F specification was introduced in and covers anchor bolts designed to anchor structural supports to concrete foundations.

Welding Contrary to popular belief, not all grade 55 material is weldable. Permanent grade identification on the end of the anchor bolt that projects from the concrete, in lieu of color coding. This field should be left blank. Finishes September 5, Threaded June 19, On the other hand, B7 is heat treated, increasing strength but rendering the material more brittle. Referenced Documents purchase tr The documents listed below are referenced within the subject standard but are not provided as part of the standard.

  LAUGHING WILD DURANG PDF

When S1 is not specified, the Grade 55 material may or may not be weldable. B7 is an alloy which includes chromium and molybdenum for added strength and corrosion resistance, rendering it suitable for applications that are highly susceptible to corrosion at high temperatures.

The anchor bolts shall also meet specified values for nominal size, body diameter, bend section, length, bend angle, and coated length.

F1554 Grade 55

Such structural supports include building columns, column supports for highway signs, street lighting and traffic signals, steel bearing plates, and similar applications. Galvanizing F grade 55 anchor bolts can be provided in either a black or galvanized condition.

The bolts shall adhere to specified elemental chemical compositions as examined by heat and product analysis. Input Your Industry required. We offer a wide selection of materials, finishes, and sizes of Figure U-Bolts. Color coding on the end — 36 blue, 55 yellow, and red — helps facilitate easy identification in the field.

F anchor bolts can take the form of either headed bolts, straight rods, or bent anchor bolts. Work Item s – proposed revisions of this standard. Instead of the standard color coding of yellow spray paint to indicate Grade 55, supplemental requirement S3 can be specified by the purchaser to have a permanent grade identification on the end of the anchor bolt that projects from the concrete. We are a prime U.

Washers are detailed in 6. If the application allows for a straight bolt, then B7 can be considered as a substitute for F Grade