ASTM A666 PDF

L Stainless Steel Sheet. ASTM A Characteristics. / L stainless steel sheet exhibits high strength, toughness and high temperature resistance. The following alloys meet the ASTM-A standard. Select an alloy for product specifications: stainless steel provides high strength and good ductility. ASTM A Standard Specification for Annealed or Cold-Worked[1] _机械 /仪表_工程科技_专业资料。ASTM A Standard.

Author: Turn Kamuro
Country: Jordan
Language: English (Spanish)
Genre: Science
Published (Last): 27 July 2014
Pages: 452
PDF File Size: 10.3 Mb
ePub File Size: 4.58 Mb
ISBN: 549-5-35132-756-2
Downloads: 24467
Price: Free* [*Free Regsitration Required]
Uploader: Vudojar

Rockwell B 95 95 Last previous edition approved in as A — Depending on the work hardening characteristics of the particular grade, either the yield or the tensile strength can be the controlling factor in meeting the properties. This specification covers austenitic stainless steels in the annealed and normally required cold-worked conditions.

The values given in parentheses are for information only. The noncontrolling factor normally asm exceed considerably the speci? ICS Number Code The steels shall aa666 to specified chemical composition requirements.

Only annealed conditions of grades speci? C Annealed material that naturally meets mechanical properties may be applied. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address a6666 at phonefaxor service astm.

ASTM A666 for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. A superscript epsilon a66 indicates an editorial change since the last revision or reapproval. Only annealed conditions of grades specifically approved by the ASME code are permitted for pressure vessel use.

  ALICIA GALLOTTI KAMASUTRA PDF

This revision of Speci? The values obtained in this manner should not, however, be taken as the actual yield strength for 0. However, in the case of dispute, tests shall be made by pressure. Wstm comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.

An alternative method of determining? Hard Elongation in 2 in. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

The specimens shall be subjected to tension test, free-bend test, and controlled-bend or V-block test. HardC Elongation in 2 in.

They shall be formed in different shapes such as sheets, strips, plates and flat bars. This standard has been approved for use by agencies of the Department of Defense. The choice of test method for materials in conditions other than annealed shall be at the option x666 the seller. Number of Tests 8. Material Test Report and Certi? Originally approved in A number in parentheses indicates the year of last reapproval.

The values given in parentheses are for information only. Current edition approved Oct. B Maximum unless otherwise indicated. Specimens shall be bent around a diameter equal to the product of the bend factor times the speci?

ASTM A Standard Specification for Annealed or Cold-Worked[1]_百度文库

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Mechanical properties such as yield strength, tensile strength, elongation, hardness, and bending shall be determined.

  3F88L-RS 17 PDF

Historical Version s – a66 previous versions of standard. A — 03 Standard Speci?

Asstm to Active This link will always route to the current Active version of the standard. This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

ASTM does not give any warranty express or implied or make any representation that ashm contents of this abstract are accurate, complete or up to date. One bend test shall be made from one end of each coil.

ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. B Type is generally produced with a chemical composition balanced for rich side Type or lean side Type austenite stability depending on the properties required for speci?

D PSS means plate, strip, sheet. In case of dispute, the offset method of determining yield strength shall be used. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?