ASTM A Standard Specification for Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser Tubes. Chemical. ASTM A/AM: Standard Specification for Electric-Resistance-Welded Carbon Steel Heat-Exchanger and Condenser Tubes. Superior Steel Oveseas is highly acclaimed manufacturer,supplier,stockholder & exporter of ASTM A Tubing,ASTM A / AM Standard Specification.
|Published (Last):||1 August 2013|
|PDF File Size:||10.74 Mb|
|ePub File Size:||16.7 Mb|
|Price:||Free* [*Free Regsitration Required]|
Within the text, wstm SI units are shown in brackets. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. The inside diameter shall not be specified.
ASTM A Carbon Steel Heat Exchanger Electric Resistance Welded Pipe
Current edition approved Oct. If a single stamp is placed on the tube by hand, this mark should not be less than 8 in. Link to Active This link will always route to the current Active version of the standard.
Tubing having other dimensions may be furnished, provided such tubes comply with all other requirements of this specification. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. Tubing having other dimensions may be furnished, provided such tubes comply with all other requirements of this speci?
Both retests, for the elements in question, shall meet the requirements of the speci? Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
This abstract is a brief summary of the referenced standard. This specification covers minimum-wall-thickness carbon steel tubes proposed for use in heat exchangers, condensers, and similar heat-transfer apparatus. The tubes shall be manufactured by electric-resistance welding and shall undergo heat treatment.
The purchaser may specify which test is to be used. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Mechanical testing of the specimens shall include a flattening test, flange test and a reverse flattening test. Combining values from the two systems may result in nonconformance with the speci?
ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Within the text, the SI units are shown in brackets. The materials under this specification shall be in accordance with other ASTM document enlisted herein unless otherwise provided. Combining values from the two systems may result in nonconformance with the specification. The specimens shall also be subjected to Brinell or Rockwell hardness test and hydrostatic or nondestructive electric test.
Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. The inside diameter shall not be speci? NOTE 1—A lot consists of tubes. A slight amount of oxidation shall not be considered as scale.
The term lot applies to all tubes prior to cutting, of the same nominal diameter and wall thickness which are produced from ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.
Historical Version s – view previous versions of standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. A number in parentheses indicates the year of last reapproval. Mechanical Tests Required The chemical composition thus determined shall conform to the requirements speci?
It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.
Cold drawn tubes shall be heat treated after the? If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
ASTM A214 Carbon Steel Tubing Manufacturer in India
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? The purchaser may specify in the order a speci?
A superscript epsilon e indicates an editorial change w214 the last revision or reapproval. Originally published as A —39 T.