Infineon 1EDIF Gate Drivers are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for Infineon 1EDIF Gate Drivers. Maximum Operating Temperature + °C, Length mm, Number of Outputs 1, Minimum Operating Supply Voltage V, Brand Infineon, Input Logic. Buy V Single IGBT Gate Driver SOIC16 1EDIF. Browse our latest mosfet-drivers offers. Free Next Day Delivery.
|Country:||Papua New Guinea|
|Published (Last):||11 January 2017|
|PDF File Size:||17.42 Mb|
|ePub File Size:||14.87 Mb|
|Price:||Free* [*Free Regsitration Required]|
Datasheet 7 Version 2. Part of this is the very special attitude of our staff. During turn-off, the gate voltage is monitored and the clamp output is activated when the gate voltage goes below 2V related to VEE2. Blanking time is provided by a highly e1d020i12 internal current source and an external capacitor.
Insulation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application. The Manufacturers reserve the right to change this Information at any time without notice. Non-Inverting and Inverting Inputs.
Low Level Clamp Voltage typ. Please select an existing parts list. Information For further information on technology, delivery terms and conditions and prices please contact your nearest Infineon Technologies Office www.
RoHS Certificate of Compliance. Further, a rail-to-rail output reduces power dissipation.
Desaturation Fault Datasheet 17 Version 2. To ensure correct switching of IGBTs the device is equipped with an undervoltage lockout for both chips.
Save this item to a new parts list. During turnoff, the gate voltage is monitored and the clamp output is activated when the gate voltage goes below 2V related to VEE2. Thank you for your feedback. The blanking time is adjustable by an 8 Version 2. Save to an existing parts list Save to a new parts list. The product detailed below complies with the specifications published by 1wd020i12 Components. Terms of delivery and rights to technical change reserved.
1edif Stock and Price by Distributor
RDY Ready status Open-drain with internal pull up resistor output to report the correct operation of the device. Datasheet 11 Version 2. You agree that the Information as provided here through an intermediary may not be error-free, accurate or up-to-date and that it is not advice.
For information on the types in question please contact your nearest Infineon Technologies C. Thermal performance may change significantly with layout and heat dissipation of components in close proximity. Furthermore, it reduces the power to be dissipated by the driver. Datasheet 1es020i12 Timer The 1EDIF incorporates two level of signal transmission security implemented through two independent watchdog timers.
Quality takes on an allencompassing significance at Semiconductor Group. A programmable blanking time is used to allow enough time for IGBT saturation. Compliance with the safety ratings shall be ensured by means of suitable protective circuits. Input IC power dissipation does not require derating.
Datasheet 16 Version 2. A minimum input pulse width is defined to filter occasional glitches. Datasheet 20 Version 2. Unit Test Conditions max. Please enter a message. Minimum Operating Supply Voltage. For us it means living up to each and every one of your demands in the best possible way. Parameter Symbol 1ed020i122 Values Unit min. Unless otherwise noted all parameters refer to GND1. We direct our efforts equally at quality of supply and logistics, service and support, as well as all the other ways in which we advise and attend to you.
If no negative supply voltage is available, both pins have to be connected to GND2.
A current of maximum mA for 10us may be fed back to the supply through one of this paths. Throughout the corporation we also think in terms of Time Optimized Processes topgreater speed on our part to give you that decisive competitive edge. Warnings Due to technical requirements components may contain dangerous substances. VCC2 Positive power supply pin of the output side. We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts stated herein.
An effective active Miller clamp function avoids the need of negative gate driving in most applications and allows the use of a simple bootstrap supply for the high side driver.
Therefore, the use of a negative supply voltage can be avoided in many applications.